Edge-rounding of planchets (kvečování)

Kvečování is a work procedure in the medieval mint in which a stack of unstrucken coin planchets was aligned in a groove, gripped with tongs, and then their edges were rounded and evened by blows of a heavy hammer. It was the preparation of planchets before further cleaning and the striking itself.

Kvečování belongs to the auxiliary operations which, in traditional hand mint production, were decisive for the quality of the resulting coin, even though they did not directly participate in the actual "image" of the strike. In the Middle Ages the production of coins was a craft process divided into several steps: from the preparation of the metal, through the creation of the blank (planchet), to the final blow of the dies. Each stage had its significance — and since work was done with a large number of pieces, the way to speed up the work while maintaining acceptable regularity was also important.

Planchets were usually produced by cutting or chopping from sheet, or from rods or strips, depending on local technology and period. The blanks thus obtained often did not have a perfectly regular shape: the edges tended to be sharper, in places jagged, the planchets could differ slightly in size, and the outer contour was not always "round" as we expect of coins. In practice this entailed several difficulties. An irregular planchet seats less well under the dies; on impact it can "slip" or the pressure is poorly distributed, and the resulting strike appears askew or is partly off the planchet. Rough edges moreover increase the risk of cracks or splintering of material during striking, especially when the metal had to behave ductilely and at the same time withstand a strong blow.

Kvečování

It was precisely here that kvečování made sense. Its essence was to align several planchets at once into a "stack", to insert them into a groove or simple guide channel, and to grip them firmly with special tongs (in the sources the designation kvečování tongs appears). The bundle thus held was then tapped with a heavy hammer so that the edges of the individual planchets were "aligned" and the outlines became more rounded. It is important that one did not work with each planchet separately — the advantage lay in batch processing and in the fact that the groove and the grip of the tongs helped to hold the pieces in one line.

Kvečování must be understood as part of a broader chain of preparatory operations. After shaping and edging followed further steps that were to "settle" the planchet and prepare it for striking. In mint practice one often speaks of the blanching of planchets (chemical or mechanical further cleaning of the surface, typically with silver strikes), and only then came the striking itself between the dies. Kvečování was thus not decorative but purely technological: the aim was a more regular geometry of the planchets, less waste, and a more uniform quality of output under conditions of hand production.

History

Because medieval coinage was largely based on experience and local tradition, kvečování cannot be firmly tied to a single place or date of introduction. In general, however, it corresponds to the logic of workshops where coins were struck in large series and where procedures were sought for speeding up routine work and reducing rejects. In numismatic study this term is important mainly when describing the technology of production: it helps to explain why some coins exhibit certain features at the edge, how more regular shape was achieved, and how the mint organised work with planchets even before the impression of the dies took place.

In simplified terms kvečování can be described in four points: the planchets were stacked, the stack was aligned in a groove, gripped with tongs, and then tapped with a heavy hammer. The blows were not aimed at the surface of the planchets but were meant to "knock down" and even out their peripheral irregularities. Appropriate force was important: blows too weak would not adjust the edges, blows too strong could cause deformation or unwanted indentations.

Procedure and practical features of kvečování

The result was planchets with a more regular outline and a smoother edge, which centred better during striking. It was precisely centring that influenced whether the coin's image would be evenly placed on the surface and whether the edge would not bear unnecessary "tearing" of metal. Kvečování thus contributed to more legible strikes and more stable production, although in itself it did not guarantee perfect appearance — that also depended on the quality of the metal, annealing, surface cleanliness, and the state of the dies. In descriptions of mint technologies the term is used because it precisely names one specific workshop step which would otherwise easily disappear under the general designation "preparation of planchets".

Return to previous page

Information

Customer account

Sign in by e-mail

We will send you a one-time code. You can also complete your order without an account.

My space

ACCOUNT

LANGUAGE

CURRENCY